Tools for Foil covered micro plates
From LEAP
(→Contact LEAP) |
|||
| Line 3: | Line 3: | ||
|image = FoilCutter1_001.jpg | |image = FoilCutter1_001.jpg | ||
|type = '''SPECIAL''' | |type = '''SPECIAL''' | ||
| - | |id = | + | |id = Microtiterplate Foil Cutter for Needles max. gauge 22 |
|description = Accessory Showcase | |description = Accessory Showcase | ||
}} | }} | ||
| Line 10: | Line 10: | ||
=== Foil Cutter === | === Foil Cutter === | ||
| + | A microplate foil cutter tool is available for safe penetration of microplate sealing foils. A wide variety of heat sealing material is offered by many vendors. The Aluminum foil has a sealing layer applied, which melts at a given temperature (range approx. 140 -180°C). The seal material is often Polypropylene (PP), Polyethylene (PE) or Polystyrene (PS). Customers have observed particles of the size of the needle diameter in the wells. These particles can clog the needle during the aspiration step or if transported and ejected the injection valve port. The microplate foil cutter pre-cuts the foil before the needle penetrates. The shape of the cutter tip prevents that particles are cut out completely. Rather than falling into the well, the foil piece | ||
| + | is still attached to the foil. The microplate foil cutter should be used with any PAL LC version, where Heat Sealing Foils are used. It is limited to max. needle gauge 22 (standard gauge for LC syringes) and can not be used with any kind of glass vial septas or for GC applications.The tool is attached to the PAL needle guide like the CombiPAL Magnetic Transport Ring. No changes in firmware settings are needed. | ||
| + | The new Foil Cutter is available from LEAP Technologies. | ||
| - | + | === Photos === | |
| + | <gallery> | ||
| + | Image:FoilCutter1_001.jpg | Foil Cutter installed in PAL | ||
| + | Image:FoilCutter2.jpg | Foil Cutter on fol plate | ||
| + | Image:Foil_Cutter_Kit.png | Foil Cutter | ||
| + | Image:Foil1.png | Foil Cutter in action | ||
| + | </gallery> | ||
=== Contact LEAP === | === Contact LEAP === | ||
* [http://www.leaptec.com/ LEAP Technologies, Inc.] | * [http://www.leaptec.com/ LEAP Technologies, Inc.] | ||
| + | |||
| + | |||
| + | Heat Sealing Foils, Particles in Wells. | ||
Revision as of 22:56, 3 April 2009
| LEAP Special Items |
| Application Type | |
| SPECIAL | |
| Application ID | |
| Microtiterplate Foil Cutter for Needles max. gauge 22 | |
| Description | |
| Accessory Showcase |
Foil Cutter
A microplate foil cutter tool is available for safe penetration of microplate sealing foils. A wide variety of heat sealing material is offered by many vendors. The Aluminum foil has a sealing layer applied, which melts at a given temperature (range approx. 140 -180°C). The seal material is often Polypropylene (PP), Polyethylene (PE) or Polystyrene (PS). Customers have observed particles of the size of the needle diameter in the wells. These particles can clog the needle during the aspiration step or if transported and ejected the injection valve port. The microplate foil cutter pre-cuts the foil before the needle penetrates. The shape of the cutter tip prevents that particles are cut out completely. Rather than falling into the well, the foil piece is still attached to the foil. The microplate foil cutter should be used with any PAL LC version, where Heat Sealing Foils are used. It is limited to max. needle gauge 22 (standard gauge for LC syringes) and can not be used with any kind of glass vial septas or for GC applications.The tool is attached to the PAL needle guide like the CombiPAL Magnetic Transport Ring. No changes in firmware settings are needed. The new Foil Cutter is available from LEAP Technologies.
Photos
Foil Cutter installed in PAL |
 Foil Cutter on fol plate |
 Foil Cutter |
 Foil Cutter in action |
Contact LEAP
Heat Sealing Foils, Particles in Wells.
